Introduction: Plaguy Twisted Nose Cannula

My one-year-old granddaughter was a micropreemie, weighing less than a pound at birth. Although she has various health issues, this does not preclude her from being very active, which in turn causes her nose cannula to kink. Since Ma and Dad send away change her cannula only every two weeks, it behind get really twined, causing kinks that diminish or cut off her aura supply. It upsets me that this happens and so I've been nerve-wracking to research everything I can to rule a solution for her. There just doesn't seem to be anything that will work for her. Sometimes the cannulas/tube are more pliable one week than they are the side by side. It's just nothing we can specifically pin down. The favorable steps are what I've come up with and it seems to be impermanent so far. I guessing fourth dimension is the correct essa. I hope it works for mortal else, too.

You can buy swivel connectors for oxygen tubing but I've not ground any kind of nose cannula with a pivot connector at the Y junction, which I think would be optimum, keeping the headset stable but allowing the principal tubing to swivel. And it's much challenging to observe something better for pediatric nose cannulas. I've also translate some atrocious reviews some swivel connectors, that they can wetting. It's very frustrating and concerning knowing your loved one's breathing may be impaired because of all the twisting that's leaving on with this apparatus.

Tools:

Nose cannula

Blow dryer

Athletic tape

Scissors

Step 1: Straightening the Tube

NOTE: The cannula used for this instructable happens to be for an adult, which the medical ply company delivered past mistake, merely the cannuals are tightly looped and guaranteed by a wallpaper band, pixilated and "curly." My original step is to make the tubing pliable and as straight every bit I can cotton on. I hang IT complete a door, gently pulling on it while heating it with the air dryer. Do not do this excessively closely to the tubing or run it over the same place for excessively long, which could damage the tubing.

Step 2: Serious Components

The initial picture is of the sliding bolo. This component slides to appropriate you to secure the tubing close to the head. The secondly pictorial matter is that of the Y joint or Y connective. It shows the two headset tubes (lanyards) that merge into the main long tubing that is socially connected to the oxygen source.

Step 3: Wraping the Headset Tubes

Athletic record works best for me. You may find something much better.

The second picture shows the Y junction on the port and the sliding bolo happening the right. It is the area betwixt the two that this instructable addresses.

Before wrapping, cast the nose cannula along the person WHO wish be wearing it and slide the bolo toward the head just allow adequate board that the bola tie arse to be slid back for remotion of the headset from the head.

To start, cut 2 pieces of tape, each about 3 inches long-wooled. Starting nearest to the sliding bolo, separate the two pieces of tubing with your fingers. Using one piece of tape, securely impound it to the inside of one of the tubes. Enclose it around the tube to which it is secured and discover the second tube on the way back (see Images 3 and 4). Profane it down along a surface, holding the tubes together tightly and continue to wrap some tubes together. As close as you can, videotape the separate piece of tape to the second tube and wrap in the paired direction of what you just did, using the old instruction for the first tubing. The method acting seems to keep the two tubes pulling in opposite directions, therefore keeping it from twisting.

Continue this subroutine all the way cut down to the Y junction. I happen to decamp about a 1/4 inch between the tapings but IT might work better for you to keep all the tapings right next to each unusual. When you demoralis to the Y junction, tape the tubes to the Y junction (see Images 6 and 7).

Footprint 4: To a greater extent Photos

These are impartial more photos that may be ministrant.

Be the Beginning to Share

Recommendations

  • Anything Goes Contest 2022

    Anything Goes Contest 2022